Featured Products

Qscan Outdoor 2-D Scanner

Qscan Mini Turnstile and Kiosk Wiegand 12V Imager

Ble1 Bluetooth/Prox Reader

Sproxjx Tri-Technology Reader (barcode / mag / prox)

QscanT Turnstile reader Wiegand 12V Imager with prox and 13.5 Mhz

Smart Prox Jx

RF reader with optional barcode and magnetic stripe. Supports IBC, Hid, Farpointe,Awid, Casi, Indala, EM prox, Iclass, Mifare, and PIV-II smartcards.

 

 
     
The Smart Prox Jx is a decoded RF reader available with proximity, Mifare, Iclass, and/or barcode and magnetic stripe. They can be used anywhere where the reading of both barcodes, magnetic stripes, and rf cards are required, such as visitor systems, security systems, time & attendance systems, hospitals, and college campuses. These readers are available in many different industry standard interfaces, are programmable, and are available with a variety of options, such as leds, relays, and door sense inputs. The Smart Prox Jx will read all hi and lo-co magstripes, at any density, most barcode symbologies, proximity cards by Hid, Farpointe, IBC, Casi, Awid, Indala, and Iclass,Mifare, and PIV-II 13mhz cards. Proximity formats can also be modified using this reader. For example, 26 bit proximity cards can be read and then reformatted into 34 bit outputs. Perfect for use in Access Control and Time & Attendance applications, and any application where the primary card technology is proximity, but temporary badges are made using barcodes or magstripes. The Smart Prox Jx is available as a combination reader, with internal proximity/rf reading, as a 1-piece prox/rf-only reader, or as a 2-piece solution, using an external read head for the proximity/rf reading. This 2-piece solution allows proximity readers with either wiegand or aba output to also use the complete functionality of IBC's "JX" series readers, such as computer control, and relay activation.  Any application which currently uses "JX" series readers using barcode or magstripe can add proximity support using any model or configuration of the Smart Prox JX. The Smart Prox Jx is firmware upgradeable, and can both read and process Kronos, Cac, Usid, and Dbids barcodes.

 

Proximity Cards Supported   IBC,HID,Farpointe, Awid,Casi,EM, Indala
13Mhz Cards Supported   Iclass, Mifare, PIV-II
Scanning Speed (barcode/mag)   3-30 ips (7-76 cm/sec)
Scan Direction (barcode/mag)   bi-directional
Symbologies (barcode)   Code39, 93, 2/5, I2/5, 128, UPCA, EAN13, Codabar
Resolution (barcode)   7 mil
Read Height (barcode)   0.4"(1cm) standard, 0.465" optional
Tracks (magstripe)   Track2, Tracks 1&2, Tracks 2&3, Tracks 1,2&3
Good Read Beep   programmable
Slot Width   0.050"(1.2mm). Other widths upon special request
Indicators   2 leds (programmable)
Light Source (barcode)   630nm visible, 940nm infrared
Temperature   -40c to +85c
Dimensions   4.6"L x 2.4"W x 1.4" H (11.6cm x 6cm x 3.5cm)
Weight   6 ounces
Material   black polycarbonate (Noryl optional)
Power   5VDC(150ma), 8-15VDC, or 15-30VDC
Standard Wiring   3' (91cm) cable w/flying leads or connectors depending on interface
Relay  

30VDC 500ma Form C
12VDC 700ma direct from POE

Sense Inputs   TTL level (minimal current draw)
Available Interfaces:   RS422/485
    TCP/IP
    USB
    Wiegand
    ABA (magstripe emulation)
    RS232 wedge
    TTL ascii
    Inverted TTL ascii
    Wand Emulation
    F2F

Programmable
Visible or Infrared Optics
-40c to +85c operation
Networkable
Reads Kronos Cards, Cac cards, Ncac cards, Usid cards, Dbids cards, Piv-II cards

5,12, or 24VDC
0.400" or 0.465" read height
Track 2, 1&2, or 2&3
Led's
Internal Relay
Sense Inputs
External keypad support
Weatherproofing
#6 or 3mm mounting
Side or Rear wiring
Noryl (chemical resistant)

Mounting Kit